Reasons Your fiat 500 key fob not working 500 Key Fob Won’t Work
A fiat 500 flip key repair 500 key fob makes it easy to open doors and start your vehicle. However, there are many reasons why the fob won’t be functioning. This could be due to a dead battery, water damage, receiver modules issues, and interference.
This listing is for an NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.
Dead Coin Battery
The most frequent reason why the 500 key fob won’t function is due to the battery is dead. Modern key fobs have a limited operating range and should be within only a few feet from the vehicle to operate. If you are further away from your vehicle and press the keyfob button, it won’t respond and display the message “Key Fob Not Detected”.
If this happens, replace the battery of your coin cell (Part number CR2032) with a new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can find them at your local hardware store or on the internet.
You can test the battery in the coin-cell by pressing the buttons while you are standing close to your fiat scudo key replacement 500. The car will blink its parking lights, and the key fob should be able to operate the lock and unlock buttons.
If your key fob does not work after replacing the battery, it might be water damage that hinders it from interacting with the module inside your vehicle. Water damage can occur in many ways, such as simply splashing or submerging the key fob into saltwater at the beach. If you suspect your fob has been exposed to water, you can try placing it in a dry rice bag to pull the moisture out. If this isn’t working, you’ll have to get your fob reprogrammed either by an auto locksmith or dealer.
Water Damage
While the fob has some rubber seals to keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater is particularly dangerous to the fob’s circuit board which causes it to short out and eventually die. The fob getting wet is not a good idea however, if you drop it into the water in a cup or do not remember to remove it from your pants pocket before running the washing machine and you don’t have a chance, don’t give in.
Take the battery off first. Clean the electronic chip using isopropyl or a similar product and then dry it thoroughly before replacing the battery. Then check the fob to see if it works. If the fob doesn’t work, it may need to be reset. This is usually done by a dealer or professional auto locksmith.
If your key is old and not programmed for your vehicle You will need to replace it completely. A professional locksmith in the automotive industry will be able to complete this process. The locksmith will need the key cut to match your vehicle’s ignition. The locksmith also needs to reprogram the fob into the car’s system. This is a fast and cost-effective procedure that can be completed on the same day.
Receiver Module Issues
One of the most common reasons your 500 key fob could stop functioning is because it’s out of range. The remote usually has 30 feet of range or less, and if it’s too far away from your car it will not respond to your commands. This can be easily fixed by moving it closer to your vehicle until it starts responding.
If you’ve replaced the coin battery (commonly called”button” or “button” or “watch”) and your fob doesn’t function, it could have an internal circuit board issue. In the majority of cases, reprogramming your fob will solve the problem. You can find the procedure for the majority of vehicles on YouTube or in the owner’s manual.
It is possible to replace the metal clips that hold the coin batteries in place. If they loose tension, it can prevent your coin battery from being properly seated and cause your remote to malfunction.
In rare cases the fob may be out of sync with your vehicle because of hardware or software issues. This can be a major headache, but you can usually resolve this issue by visiting a local dealer or auto locksmith to reprogram your fob. In certain instances they may have to reinstall the software on your body control module, too.
Interference
In addition to a dead coin battery The key fob may not be able to transmit or receive the signal due to interference. This could occur if the keyfob is in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons why the key fob might not function could be due to a weak connection to the buttons, damage to the internal chip or water damage.
If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. replacing batteries, reprogramming or using the spare key for fiat 500 key fob, you could have a malfunctioning receiver module on your 500. The receiver module, located beneath the dashboard, receives radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.
There’s a quick and easy way to reset the 500’s on-board system including the keyfob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electricity, and allow you to restart the car’s computer. This can help get your key fob working again. If the issue persists, you should seek the advice of an expert technician. They will be able to identify the exact cause of any problems.